检测项目(部分)
交流电源端口电压暂将、短时中断和变化
检测样品(部分)
动作功能与电源电压无关的(RCCB)
检测标准(部分)
国家标准 GB 3368-1982 工业自动化仪表用电源电压
【适用范围】
【中国标准分类】 K31 工业自动化仪表与控制装置
【国际标准分类】 29.120.50-熔断器和其他过载保护装置
国家标准 GB/T 16916.22-2008 家用和类似用途的不带过电流保护的剩余电流动作断路器(RCCB) 第22部分:一般规则对动作功能与电源电压有关的RCCB的适用性
【适用范围】n本部分适用于交流额定电压不超过440V,额定电流不超过125A的主要用于防电击保护的动作功能与电源电压有关的家用和类似用途的不带过电流保护的剩余电流动作断路器(RCCB)。
【中国标准分类】 K31 低电压器
【国际标准分类】 29.120.50-熔断器和其他过载保护装置
国家标准 GB/T 16917.21-2008 家用和类似用途的带过电流保护的剩余电流动作断路器(RCBO) 第21部分:一般规则对动作功能与电源电压无关的RCBO的适用性
【适用范围】本部分适用于交流50Hz或60Hz,额定电压不超过440V,额定电流不超过125A,额定短路能力不超过25000A的动作功能与电源电压无关的家用和类似用途的带过电流保护的剩余电流动作断路器(RCBO)。
【中国标准分类】 K31 低电压器
【国际标准分类】 29.120.50-熔断器和其他过载保护装置
国家标准 GB/T 16917.22-2008 家用和类似用途的带过电流保护的剩余电流动作断路器(RCBO) 第22部分:一般规则对动作功能与电源电压有关的RCBO的适用性
【适用范围】本部分适用于交流50Hz或60Hz,额定电压不超过440V,额定电流不超过125A,额定短路能力不超过25000A的动作功能与电源电压有关的家用和类似用途的带过电流保护的剩余电流动作断路器(RCBO)。
【中国标准分类】 K31 低电压器
【国际标准分类】 29.120.50-熔断器和其他过载保护装置
国家标准 GB/T 19212.5-2011 电源电压为1100V及以下的变压器、电抗器、电源装置和类似产品的安全. 第5部分:隔离变压器和内装隔离变压器的电源装置的特殊要求和试验
【适用范围】GB 19212.1-2008的该章用下列内容代替: n本部分规定了一般用途隔离变压器和内装一般用途隔离变压器的电源装置的安全方面的要求。带 n有电子电路的变压器也包括在本部分中。 n本部分适用于驻立式或移动式、单相或多相、空气冷却(自冷或风冷)、独立用和配套用的干式变压 n器。其绕组可以是包封式或非包封式。 n额定电源电压不超过交流1100V
额定频率及内部运行频率不超过500Hz。 n额定输出不超过: n--对单相变压器
25kVA; n--对多相变压器
40kVA。 n如果采购方和制造方另有协议时
本部分也适用于对额定输出不限制的变压器。 n本部分不适用于预定要与变压器的输入和输出端子连接的外部电路及其元器件。 n本部分适用于在安装规程或设备规范中要求电路间的绝缘为双重绝缘或加强绝缘的变压器。
【中国标准分类】 K41 输变电设备
【国际标准分类】 29.180-变压器、电抗器
国家标准 GB/T 19212.7-2012 电源电压为1 100V及以下的变压器、电抗器、电源装置和类似产品的安全 第7部分:安全隔离变压器和内装安全隔离变压器的电源装置的特殊要求和试验
【适用范围】GB 19212的本部分规定了一般用途安全隔离变压器和内装一般用途安全隔离变压器的电源装置的安全方面的要求。带有电子电路的变压器也包括在本部分中。除非另有规定
以下“变压器”包括一般用途安全隔离变压器和内装一般用途安全隔离变压器的电源装置。本部分适用于驻立式或移动式、单相或多相、空气冷却(自冷或风冷)
独立用和配套用的干式变压器。其绕组可以是包封式或非包封式。额定电源电压不超过交流1100 V
额定频率及内部运行频率不超过500Hz。额定输出不超过:对单相变压器
为10 kVA;对多相变压器
为16 kVA。如果采购方和制造方另有协议时
本部分也适用于对额定输出不限制的变压器。空载输出电压或额定输出电压不超过交流50 V或无纹波直流120 V。本部分不适用于预定要与变压器的输入和输出端子连接的外部电路及其元器件。本部分适用于在安装规程或设备规范中要求电路间的绝缘为双重绝缘或加强绝缘的变压器。
【中国标准分类】 K41 输变电设备
【国际标准分类】 29.180-变压器、电抗器
国家标准 GB/T 19212.14-2012 电源电压为1100V及以下的变压器、电抗器、电源装置和类似产品的安全 第14部分:自耦变压器和内装自耦变压器的电源装置的特殊要求和试验
【适用范围】GB 19212的本部分规定了一般用途自耦变压器和内装一般用途自耦变压器的电源装置的安全方面的要求。带有电子电路的变压器也包括在本部分中。除非另有规定
以下“变压器”包括一般用途自耦变压器和内装一般用途自耦变压器的电源装置。本部分适用于驻立式或移动式、单相或多相、空气冷却(自冷或风冷)
独立用和配套用的干式变压器。其绕组可以是包封式或非包封式。额定电源电压不超过交流1100 V
额定频率及内部运行频率不超过500Hz。铁心容量不超过:对单相变压器
为2 kVA;对多相变压器
为10 kVA。额定输出不超过:对单相变压器
为40 kVA;对多相变压器
为200 kVA。如果采购方和制造方另有协议时
本部分也适用于对铁心容量和额定输出不限制的变压器。如果适用时
空载输出电压或额定输出电压不超过交流1000V或无纹波直流1415V
且对独立用变压器
空载输出电压或额定输出电压不超过交流50V或无纹波直流120V。本部分不适用于预定要与变压器的输入和输出端子连接的外部电路及其元器件。本部分包括的变压器只适用于在安装规程或最终产品标准要求电路间不绝缘的场合。
【中国标准分类】 K41 输变电设备
【国际标准分类】 29.180-变压器、电抗器
国家标准 GB/T 19212.17-2019 电源电压为1100V及以下的变压器、电抗器、电源装置和类似产品的安全 第17部分:开关型电源装置和开关型电源装置用变压器的特殊要求和试验
【适用范围】GB/T19212.1-2016的该章用下列内容代替:
GB/T19212的本部分规定了开关型电源装置和开关型电源装置用变压器的安全要求。带有电子 线路的变压器也包括在本部分中。
注1:安全要求包括电气、温度和机械方面。
本部分适用于:
a)内装安全隔离变压器、提供符合GB/T 17045和GB/T 16895.21规定的交流或直流SELV、 PELV或FELV输出电压或其中的某种组合的输出电压、用于家用和其他消费类产品的开关型电源装置,但GB8898、IEC61347系列、IEC61204-7和GB4943.1包含的产品除外;
b)最高输出电压不超过交流1000V或无纹波直流1414V的家用和其他消费类产品的开关型 电源装置,但在a)项中包含的产品、GB8898、IEC61347系列、IEC61204-7和GB4943.1包含的产品除外;
c)本部分可用于开关型电源装置内使用的变压器(见附录BB)。
本部分包含的安全要求用于:
——对应于GB/T19212.2的一般用途分离SMPS;
——对应于GB/T19212.5的一般用途隔离SMPS;
——对应于GB/T19212.7的一般用途安全隔离SMPS;
——对应于GB/T19212.14的一般用途自耦SMPS。
对应于GB/T19212系列其他部分特定应用的SMPS,其相应要求适用。此外,本部分列出的要求也适用。当两项标准不一致时,优先采用更严格的标准。
注2:由于内部变压器的最高额定电源电压为1000v,因为整流方式的原因,开关型电源的最高额定电源电压可能较低。
本部分包含驻立式或移动式、单相或多相、空气冷却(自冷或风冷)、独立或配套用开关型电源装置, 其额定电源电压不超过交流1100V,额定电源频率不超过500Hz,额定内部工作频率超过500Hz,但 不超100MHz,额定输出不超过1kVA或1kW,内装包封绕组或非包封绕组的干式变压器。
本部分附录BB所包含的开关型电源装置用配套变压器的额定输出不超过:
——对单相变压器,为25kVA;
——对多相变压器,为40kVA。
注3:对更高的频率需要附加要求,但本部分可以作为导则使用。
开关型电源装置的空载输出电压或额定输出电压不超过:
——当使用分离变压器或自耦变压器时,为交流1000V或无纹波直流1415V;
——当使用隔离变压器时,为交流500V或无纹波直流708V;
——当使用安全隔离变压器时,为交流50V或无纹波直流120V.。
对于独立的开关型电源装置,当使用分离变压器或自耦变压器时,空载输出电压或额定输出电压不低于交50V或无纹波直流120V。
本部分也适用于额定输出不受限制的开关型电源装置、变流器和逆变器,但是这样的开关型电源是特殊应用,要按供需双方之间的协议。
注4:本部分上下文中,将变流器和逆变器都视为开关型电源装置。
对于未包含在本部分的范围、IEC61204-7的范围或IEC61347系列的范围内的产品,本部分也可以作为导则使用。
本部分不适用于:
——发电机组;
—— IEC62040规定的不间断电源(UPS);
——IEC61204-7(即:低压电源装置、直流输出、性能参数)包含的开关型电源装置、直流电源和配电设备及GB4943.1、GB4793.1、GB9706.1和GB8898所适用的开关型电源装置;
——IEC61347包含的灯控制装置;
——预定要与变压器的输入端子和输出端子连接的外部电路及其元器件。
注5:IEC61204-7由IEC/TC22的SC22E更新。
注6:注意以下情况:
——对预定用在车辆、船舶或飞机上的变压器,可能需要附加要求(按其他适用的标准、国家规程等); ——可考虑采取措施使外壳及其内部元器件不受外界影响,如霉菌、虫蛀、白蚁、太阳辐射和冰冻;
——宜考虑变压器在运输、储存和运行方面的不同条件;
——对预定用于特殊环境的变压器,例如热带环境,可以采用符合其他适用的标准和国家规程的附加要求。
注7:随着今后变压器技术的发展,可能需要提高变压器频率的上限值,到那时之前,可以将本部分作为导则使用。 除非另有规定,在此之后的术语SMPS包括开关型电源装置。
GB/T19212的本部分规定了开关型电源装置和开关型电源装置用变压器的安全要求。带有电子 线路的变压器也包括在本部分中。
注1:安全要求包括电气、温度和机械方面。
本部分适用于:
a)内装安全隔离变压器、提供符合GB/T 17045和GB/T 16895.21规定的交流或直流SELV、 PELV或FELV输出电压或其中的某种组合的输出电压、用于家用和其他消费类产品的开关型电源装置,但GB8898、IEC61347系列、IEC61204-7和GB4943.1包含的产品除外;
b)最高输出电压不超过交流1000V或无纹波直流1414V的家用和其他消费类产品的开关型 电源装置,但在a)项中包含的产品、GB8898、IEC61347系列、IEC61204-7和GB4943.1包含的产品除外;
c)本部分可用于开关型电源装置内使用的变压器(见附录BB)。
本部分包含的安全要求用于:
——对应于GB/T19212.2的一般用途分离SMPS;
——对应于GB/T19212.5的一般用途隔离SMPS;
——对应于GB/T19212.7的一般用途安全隔离SMPS;
——对应于GB/T19212.14的一般用途自耦SMPS。
对应于GB/T19212系列其他部分特定应用的SMPS,其相应要求适用。此外,本部分列出的要求也适用。当两项标准不一致时,优先采用更严格的标准。
注2:由于内部变压器的最高额定电源电压为1000v,因为整流方式的原因,开关型电源的最高额定电源电压可能较低。
本部分包含驻立式或移动式、单相或多相、空气冷却(自冷或风冷)、独立或配套用开关型电源装置, 其额定电源电压不超过交流1100V,额定电源频率不超过500Hz,额定内部工作频率超过500Hz,但 不超100MHz,额定输出不超过1kVA或1kW,内装包封绕组或非包封绕组的干式变压器。
本部分附录BB所包含的开关型电源装置用配套变压器的额定输出不超过:
——对单相变压器,为25kVA;
——对多相变压器,为40kVA。
注3:对更高的频率需要附加要求,但本部分可以作为导则使用。
开关型电源装置的空载输出电压或额定输出电压不超过:
——当使用分离变压器或自耦变压器时,为交流1000V或无纹波直流1415V;
——当使用隔离变压器时,为交流500V或无纹波直流708V;
——当使用安全隔离变压器时,为交流50V或无纹波直流120V.。
对于独立的开关型电源装置,当使用分离变压器或自耦变压器时,空载输出电压或额定输出电压不低于交50V或无纹波直流120V。
本部分也适用于额定输出不受限制的开关型电源装置、变流器和逆变器,但是这样的开关型电源是特殊应用,要按供需双方之间的协议。
注4:本部分上下文中,将变流器和逆变器都视为开关型电源装置。
对于未包含在本部分的范围、IEC61204-7的范围或IEC61347系列的范围内的产品,本部分也可以作为导则使用。
本部分不适用于:
——发电机组;
—— IEC62040规定的不间断电源(UPS);
——IEC61204-7(即:低压电源装置、直流输出、性能参数)包含的开关型电源装置、直流电源和配电设备及GB4943.1、GB4793.1、GB9706.1和GB8898所适用的开关型电源装置;
——IEC61347包含的灯控制装置;
——预定要与变压器的输入端子和输出端子连接的外部电路及其元器件。
注5:IEC61204-7由IEC/TC22的SC22E更新。
注6:注意以下情况:
——对预定用在车辆、船舶或飞机上的变压器,可能需要附加要求(按其他适用的标准、国家规程等); ——可考虑采取措施使外壳及其内部元器件不受外界影响,如霉菌、虫蛀、白蚁、太阳辐射和冰冻;
——宜考虑变压器在运输、储存和运行方面的不同条件;
——对预定用于特殊环境的变压器,例如热带环境,可以采用符合其他适用的标准和国家规程的附加要求。
注7:随着今后变压器技术的发展,可能需要提高变压器频率的上限值,到那时之前,可以将本部分作为导则使用。 除非另有规定,在此之后的术语SMPS包括开关型电源装置。
【中国标准分类】 K41 输变电设备
【国际标准分类】 29.180-变压器、电抗器
国家标准 GB/T 19212.17-2013 电源电压为1 100V及以下的变压器、电抗器、电源装置和类似产品的安全 第17部分:开关型电源装置和开关型电源装置用变压器的特殊要求和试验
【适用范围】GB19212.1—2008的该章用下列内容来代替: n本部分规定了开关型电源装置和开关型电源装置用变压器的安全方面的要求。带有电子电路的变压器也包括在本部分中。 n注1:包括电气、温度和机械方面的安全。 n本部分适用于: na) 内装安全隔离变压器
提供符合IEC61140和IEC60364-4-41规定的交流或直流SELV、PELV 或FELV 输出电压或其中的某种组合的输出电压
用于家用和其他消费类产品的开关型电源装置
但IEC60065、IEC61347系列、IEC61204-7和IEC60950-1包含的产品除外; nb) 最高输出电压不超过交流1000V 或无纹波直流1414V、用于家用和其他消费类产品的开关型电源装置
但在a)中包含的产品和IEC60065、IEC61347系列、IEC61204-7和IEC60950-1包含的产品除外; nc) 本部分可用于开关型电源装置内使用的变压器(见附录BB)。 n本部分包含的安全要求用于: n———对应于IEC61558-2-1的一般用途分离SMPS; n———对应于IEC61558-2-4的一般用途隔离SMPS; n———对应于IEC61558-2-6的一般用途安全隔离SMPS; n———对应于IEC61558-2-13的一般用途自耦SMPS。 n对应于IEC61558系列其他第2部分的特定应用的SMPS
其相应第2部分的必需的要求适用。 n此外
本部分列出的要求也适用。如果这两个要求有冲突
优先考虑最严酷的要求。 n注2:由于内部变压器的最高额定电源电压为1000V
因为整流方式的原因
开关型电源最高额定电源电压可能低一些。 n本部分包含驻立式或移动式、单相或多相、空气冷却(自然冷却或强制冷却)、独立用或配套用开关型电源装置
其额定电源电压不超过交流1100V
额定电源频率不超过500Hz
额定内部运行频率超过500Hz
但不超过100MHz
额定输出不超过1kVA 或1kW
内装包封绕组或非包封绕组的干式变压器。 n本部分附录BB所包括的开关型电源装置的配套用变压器
其额定输出不应超过: n———对单相变压器
为25kVA; n———对多相变压器
为40kVA。 n注3:对更高的频率需要附加要求
但本部分可以作为导则使用。 n开关型电源装置的空载输出电压或额定输出电压不应超过: n———当使用分离变压器或自耦变压器时
为交流1000V 或无纹波直流1415V; n———当使用隔离变压器时
为交流500V 或无纹波直流708V; n———当使用安全隔离变压器时
为交流50V 或无纹波直流120V。
【中国标准分类】 K41 输变电设备
【国际标准分类】 29.180-变压器、电抗器
国家标准 GB/T 30104.205-2013 数字可寻址照明接口 第205部分:控制装置的特殊要求 白炽灯电源电压控制器(设备类型4)
【适用范围】GB/T 30104的本部分规定了与白炽灯相关的、电子控制装置的数字信号控制协议和测试程序。
【中国标准分类】 N10 电气照明
【国际标准分类】 25.040-工业自动化系统
行业标准 JB/T 6239.2-2007 工业自动化仪表通用试验方法 第2部分:电源电压频率变化抗扰度试验
【适用范围】JB/T 6239的本部分规定了工业自动化仪表电源电压频率变化抗扰度试验的试验方法,包括试验设备、试验配置、试验程序及试验结果和试验报告。n本部分适用于工业自动化仪表电源电压平率变化抗扰度的性能评定。
【中国标准分类】 N10 工业自动化仪表与控制装置
【国际标准分类】 25.040.40-工业过程的测量与控制
行业标准 JB/T 6239.2-1992 工业自动化仪表通用试验方法 电源电压频率变化影响
【适用范围】
【中国标准分类】 N10 工业自动化仪表与控制装置
【国际标准分类】 25.040.40-工业过程的测量与控制
行业标准 JB/T 6239.3-1992 工业自动化仪表通用试验方法 电源电压低降影响
【适用范围】
【中国标准分类】 N10 工业自动化仪表与控制装置
【国际标准分类】 25.040-工业自动化系统
行业标准 JB/T 8207-1995 核仪器电源电压
【适用范围】本标准规定了核仪器用电池和直流稳压电源供电的直流电压标称值。rn本标准适用于交流、直流供电的核仪器电源。rn
【中国标准分类】 L56 核仪器与核探测器
【国际标准分类】 31.200-集成电路、微电子学
地方标准 CNS 10700-1994 手握式电源电压操作的圆锯性能测量方法
【适用范围】本标准规定电机电子设备用有关电源、电压等之图符号。
【中国标准分类】 K64 电气设备与器具
【国际标准分类】 79.120-木工设备
国际标准 ISO 7637-2-2004 道路车辆--拖曳和拖曳式车辆电气连接的连接器--第2部分:制动系统的连接器和具有12伏额定电源电压的车辆的运行装置
【适用范围】This part of ISO 7638 gives the dimensions of
and specifies the contact allocation and tests and test requirements for
connectors for the electrical connection of the braking systems and running gear of towing and towed vehicles with 12 V nominal supply voltage. In addition
it specifies a park socket used to receive and store the plug when disconnected.
【中国标准分类】 T35 汽车底盘与车身
【国际标准分类】 43.040.10-电气和电子设备
国际标准 ISO 25981-2008 测量、控制和实验室用电气设备的安全性要求--第2-033部分:家用的和专业用的测量电源电压的手持式万用表和其他手持式表的特殊要求
【适用范围】This clause of Part 1 is applicable except as follows:n1.1.1 Equipment included in scopenReplacement:nReplace the existing text with the following:nThis part of IEC 61010 specifies safety requirements for METERS.nThe METERS that have a primary purpose of measuring voltage on a live MAINS CIRCUIT are within the scope of this standard. They have various names
but all of them have capability for measurements of voltages on a live MAINS CIRCUIT. Some of the names given to this equipment are as follows:n– MULTIMETER;n– digital MULTIMETER;n– VOLTMETER;n– clamp METER (see also Part 2-032).nFor the purpose of this standard
the term METER is used for these HAND-HELD measuring instruments.nNOTE Parts of the equipment that are not within the scope of this Part 2-033 are considered to be covered by the requirements of Part 1 or other part 2's of IEC 61010 and then will also need to meet the requirements of these other parts.n1.1.2 Equipment excluded from scopenAddition:nAdd the following new item to the list:naa) IEC 61557 (Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing
measuring or monitoring of protective measures – Parts 1 through 12).nAddition:nAdd the two following paragraphs at the end of the subclause:nEquipment that is not capable of measuring MAINS voltages is not within the scope of this Part 2-033. See IEC 61010-2-030 for requirements pertaining to such equipment.)nSuch equipment
including other HAND-HELD equipment such as oscilloscopes
wattmeters
process control MULTIMETERS
and communications test sets is not within the scope of this Part 2-033.n1.2.1 Aspects included in scopenAddition:nAdd the following paragraph at the end of the subclause:nRequirements for protection against HAZARDS resulting from NORMAL USE and REASONABLY FORESEEABLE MISUSE of measuring circuits are given in Clause 101.
【中国标准分类】 K41 电工仪器仪表
【国际标准分类】 29.180-变压器、电抗器
国际标准 IEC 61558-2-16-2009 电源电压>50V普通照明用自镇流发光二极管灯--性能要求
【适用范围】This International Standard specifies the performance requirements
together with the test
methods and conditions required to show compliance of LED lamps with integral means for
stable operation intended for domestic and similar general lighting purposes having:
• a rated power up to 60 W;
• a rated voltage of > 50 V a.c. up to 250 V a.c.;
• a lamp cap as listed in IEC 62560.
These performance requirements are additional to the safety requirements in IEC 62560.
The only feature provided by this standard when applied for replacement purposes is
information on maximum lamp outlines.
The requirements of this standard relate to type testing. This standard covers LED lamps that
intentionally produce white light based on inorganic LEDs.
Recommendations for whole product testing or batch testing are under consideration.
The life time of LED lamps is in most cases much longer than the practical test times.
Consequently verification of manufacturer’s life time claims cannot be made in a sufficiently
confident way because projecting test data further in time is not standardised. For that
reason the acceptance or rejection of a manufacturer's life time claim past an operational
time as stated in 7.1 is out of the scope of this standard.
Instead of life time validation this standard has opted for lumen maintenance codes at a
defined finite test time. Therefore the code number does not imply a prediction of achievable
life time. The categories represented by the code are lumen-depreciation character
categories showing behaviour in agreement with manufacturer’s information provided before
the test is started.
In order to validate a life time claim several methods of test data extrapolation exist. A
general method of projecting measurement data beyond limited test time is under
consideration.
The pass/fail criterion of the life time test as defined in this standard is different from the life
time metrics claimed by manufacturers. For explanation of recommended life time metrics
see Annex E.
NOTE When lamps are operated in a luminaire the claimed performance data can deviate from the values established via this standard due to e.g. luminaire components that impact the performance of the lamp. It can be expected that self-ballasted LED lamps which comply with this standard will start and operate satisfactorily at voltages between 92 % and 106 % of rated supply voltage and at an ambient air temperature between –20 °C and 40 °C and in a luminaire complying with IEC 60598-1.
If a supplier claims suitability for operation at different conditions (for instance at higher voltage temperature or humidity) then:
a) Lamps shall be tested under claimed different conditions; and
b) Lamps shall start and operate satisfactorily under claimed different conditions; and
c) Lamps shall meet the performance claims under the claimed different conditions which may differ from the general conditions for measurement specified in A.1.
methods and conditions required to show compliance of LED lamps with integral means for
stable operation intended for domestic and similar general lighting purposes having:
• a rated power up to 60 W;
• a rated voltage of > 50 V a.c. up to 250 V a.c.;
• a lamp cap as listed in IEC 62560.
These performance requirements are additional to the safety requirements in IEC 62560.
The only feature provided by this standard when applied for replacement purposes is
information on maximum lamp outlines.
The requirements of this standard relate to type testing. This standard covers LED lamps that
intentionally produce white light based on inorganic LEDs.
Recommendations for whole product testing or batch testing are under consideration.
The life time of LED lamps is in most cases much longer than the practical test times.
Consequently verification of manufacturer’s life time claims cannot be made in a sufficiently
confident way because projecting test data further in time is not standardised. For that
reason the acceptance or rejection of a manufacturer's life time claim past an operational
time as stated in 7.1 is out of the scope of this standard.
Instead of life time validation this standard has opted for lumen maintenance codes at a
defined finite test time. Therefore the code number does not imply a prediction of achievable
life time. The categories represented by the code are lumen-depreciation character
categories showing behaviour in agreement with manufacturer’s information provided before
the test is started.
In order to validate a life time claim several methods of test data extrapolation exist. A
general method of projecting measurement data beyond limited test time is under
consideration.
The pass/fail criterion of the life time test as defined in this standard is different from the life
time metrics claimed by manufacturers. For explanation of recommended life time metrics
see Annex E.
NOTE When lamps are operated in a luminaire the claimed performance data can deviate from the values established via this standard due to e.g. luminaire components that impact the performance of the lamp. It can be expected that self-ballasted LED lamps which comply with this standard will start and operate satisfactorily at voltages between 92 % and 106 % of rated supply voltage and at an ambient air temperature between –20 °C and 40 °C and in a luminaire complying with IEC 60598-1.
If a supplier claims suitability for operation at different conditions (for instance at higher voltage temperature or humidity) then:
a) Lamps shall be tested under claimed different conditions; and
b) Lamps shall start and operate satisfactorily under claimed different conditions; and
c) Lamps shall meet the performance claims under the claimed different conditions which may differ from the general conditions for measurement specified in A.1.
【中国标准分类】 K70 电气照明
【国际标准分类】 29.140.01-电灯综合
国际标准 IEC 62612-2013 电源电压>50V普通照明用自镇流发光二极管灯--性能要求
【适用范围】This International Standard specifies the performance requirements
together with the test methods and conditions
required to show compliance of LED lamps with integral means for stable operation
intended for domestic and similar general lighting purposes
having: -- a rated power up to 60 W; -- a rated voltage of > 50 V a.c. up to 250 V a.c.; -- a lamp cap as listed in IEC 62560. These performance requirements are additional to the safety requirements in IEC 62560. The only feature provided by this standard
when applied for replacement purposes
is information on maximum lamp outlines. The requirements of this standard relate to type testing. This standard covers LED lamps that intentionally produce white light
based on inorganic LEDs. Recommendations for whole product testing or batch testing are under consideration. The life time of LED lamps is in most cases much longer than the practical test times. Consequently
verification of manufacturer’s life time claims cannot be made in a sufficiently confident way
because projecting test data further in time is not standardised. For that reason the acceptance or rejection of a manufacturer's life time claim
past an operational time as stated in 7.1
is out of the scope of this standard. Instead of life time validation
this standard has opted for lumen maintenance codes at a defined finite test time. Therefore
the code number does not imply a prediction of achievable life time. The categories
represented by the code
are lumen-depreciation character categories showing behaviour in agreement with manufacturer’s information
provided before the test is started. In order to validate a life time claim
several methods of test data extrapolation exist. A general method of projecting measurement data beyond limited test time is under consideration. The pass/fail criterion of the life time test as defined in this standard is different from the life time metrics claimed by manufacturers. For explanation of recommended life time metrics
see Annex E. NOTE When lamps are operated in a luminaire the claimed performance data can deviate from the values established via this standard due to e.g. luminaire components that impact the performance of the lamp.
【中国标准分类】 K70 电气照明
【国际标准分类】 29.140.01-电灯综合
国际标准 IEC 62838-2015 电源电压不超过50V交流有效值或无纹波直流120V的普通照明用LEDsi灯--安全规范
【适用范围】This International Standard specifies the safety and interchangeability requirements
together with the test methods and conditions
required to show compliance of LED lamps with integrated means for stable operation
intended for domestic and similar general lighting purposes
having:
– a rated power up to 60 W
– a rated voltage equal to or less than 50 V a.c. r.m.s. or equal or less 120 V ripple free d.c.
– caps according to Table 1.
NOTE 1 The value of 60 W rated power is under consideration. Heat management may require lower power.
This standard shall be used for products in conjunction with ELV lighting installations.
With reference to IEC 60364-7-715 in ELV lighting installations only SELV sources are applied. Where bare conductors are used the maximum lamp voltage shall be 25 V a.c. or 60 V d.c.
The requirements of this standard relate only to type testing.
For lamps > 25 V a.c. or 60 V d.c. recommendations for whole production testing or batch testing are given in IEC 60598-1 Table Q.1 column class III luminaire column 4 or 5.
NOTE 2 Where in this standard the term “lamp(s)” is used it is understood to stand for semi-integrated LED lamp(s) with supply voltages as in the scope above except where it is obviously assigned to other types of lamps.
– a rated power up to 60 W
– a rated voltage equal to or less than 50 V a.c. r.m.s. or equal or less 120 V ripple free d.c.
– caps according to Table 1.
NOTE 1 The value of 60 W rated power is under consideration. Heat management may require lower power.
This standard shall be used for products in conjunction with ELV lighting installations.
With reference to IEC 60364-7-715 in ELV lighting installations only SELV sources are applied. Where bare conductors are used the maximum lamp voltage shall be 25 V a.c. or 60 V d.c.
The requirements of this standard relate only to type testing.
For lamps > 25 V a.c. or 60 V d.c. recommendations for whole production testing or batch testing are given in IEC 60598-1 Table Q.1 column class III luminaire column 4 or 5.
NOTE 2 Where in this standard the term “lamp(s)” is used it is understood to stand for semi-integrated LED lamp(s) with supply voltages as in the scope above except where it is obviously assigned to other types of lamps.
【中国标准分类】 K72 电气照明
【国际标准分类】 29.140-电灯及有关装置
国外标准 BS 3999-17-1993 家用电器性能测量方法.第17部分:手提式电源电压操作喷枪
【适用范围】Defines principle performance characteristics and describes standard methods for measuring these characteristics.
【中国标准分类】 Y69 家用电器、日用机具
【国际标准分类】 87.100-涂料涂覆设备
国外标准 BS EN ISO 11446-2004 道路车辆.牵引车和挂车的电气连接用连接器.标称电源电压为12V的车辆用13极连接器
【适用范围】ISO 11446:2004 specifies the dimensional characteristics of
and contact allocation and tests and requirements for
13-pole connectors for the electrical connection of towing and towed vehicles with 12 V nominal supply voltage. It also specifies a park socket for receiving and storing the plug when it is disconnected.nn
【中国标准分类】 T36 车用电子、电气设备与仪表
【国际标准分类】 43.040.10-电气和电子设备
国外标准 BS EN 15207-2014 危险物品运输罐.危险区域中用24V标称电源电压设备用插头/插座连接和电源特性
【适用范围】
【中国标准分类】 低电压器
【国际标准分类】 43.040.10-电气和电子设备
国外标准 BS ISO 21848-2005 道路车辆.电源电压42 V的电气和电子设备.电负载
【适用范围】ISO 21848:2005 describes the electrical loads that can affect electric and electronic systems and components of road vehicles for a supply voltage of 42 V which may be used in a multiple voltage electrical system.nnIn addition it specifies the tests and resulting requirements
test equipment accuracy being agreed upon between the vehicle manufacturer and the supplier.nnThis International Standard also provides design guidance for the interaction of 42 V with other system voltages.n
【中国标准分类】 T35 车用电子、电气设备与仪表
【国际标准分类】 43.040.10-电气和电子设备
国外标准 BS ISO 25981-2008 道路车辆.牵引车和挂车之间电气连接用连接器.具有12V或24V标称电源电压的电子监控充电系统用连接器
【适用范围】ISO 25981:2008 specifies dimensional characteristics
contact allocation
tests and requirements of 7-pole connectors for electrical connections of electronically monitored charging systems of towing and towed vehicles. The electronic monitoring system is designed to detect 12 V and 24 V nominal supply voltage and to limit the current to 50 A. This is a connector without breaking capacity.nnThis electrical connection is intended for use with separable truck-trailer combinations in order to connect an additional battery pack of the trailer with the generator of the truck using an electronically monitored charging system. Additional battery packs in trailers are basically used with tailgate lifts
electrical forklifts or other technical equipment with high current consumption.nnISO 25981:2008 further specifies a park socket used to receive and store the plug when it is disconnected.n
【中国标准分类】 T36 车用电子、电气设备与仪表
【国际标准分类】 43.040.10-电气和电子设备
国外标准 BS EN 61558-2-4-2009 数字可寻址灯光接口.控制装置的详细要求.白炽灯用电源电压控制器(设备类型4)
【适用范围】Replacement:nThis part of IEC 61558 deals with the safety of isolating transformers for generalnapplications and power supply units incorporating isolating transformers for generalnapplications. Transformers incorporating electronic circuits are also covered by thisnstandard.nNOTE 1 Safety includes electrical
thermal and mechanical aspects.nUnless otherwise specified
from here onward
the term transformer covers isolatingntransformers for general applications and power supply units incorporating isolatingntransformers for general applications.nNOTE 2 For power supply units (linear) this part is applicable. For switch mode power supply units
IEC 61558-2-16 isnapplicable together with this part.nThis part is applicable to stationary or portable
single-phase or polyphase
air-cooledn(natural or forced) independent or associated dry- type transformers. The windings may benencapsulated or non-encapsulated.nThe rated supply voltage does not exceed 1 100 V a.c.
and the rated supply frequencynand the internal operating frequencies do not exceed 500 Hz.nThe rated output does not exceed:n– 25 kVA for single-phase transformers;n– 40 kVA for polyphase transformers.nThis part is applicable to transformers without limitation of the rated output subject to annagreement between the purchaser and the manufacturer.nNOTE 3 Transformers intended to supply distribution networks are not included in the scope.nThe no-load output voltage or the rated output voltage does exceed 50 V a.c. or 120 Vnripple-free d.c.
and where applicable
does not exceed 500 V a.c. or 708 V ripple-free d.c.nThe no-load output voltage and the rated output voltage may be up to 1 000 V a.c. orn1 415 V ripple-free d.c. for special applications.nThis part is not applicable to external circuits and their components intended to be connectednto the input terminals and output terminals of the transformers.nTransformers covered by this part are used in applications where double or reinforcedninsulation between circuits is required by the installation rules or by the end productnstandard.nNOTE 4 Attention is drawn to the following:n- for transformers intended to be used in vehicles
on board ships
and aircraft
additional requirements (fromnother applicable standards
national rules
etc.) may be necessary;n- measures to protect the enclosure and the components inside the enclosure against external influences suchnas fungus
vermin
termites
solar-radiation
and icing should also be considered;n- the different conditions for transportation
storage
and operation of the transformers should also benconsidered;n- additional requirements in accordance with other appropriate standards and national rules may be applicable tontransformers intended for use in special environments.nNOTE 5 Future technological development of transformers may necessitate a need to increase the upper limit ofnthe frequencies
until then this part may be used as a guidance document.
【中国标准分类】 N29 电气照明
【国际标准分类】 19.080-电工和电子试验
相关检测内容
- 无相关信息